Finlux 47F9076-T Manual do Utilizador descarregar pdf (Página 29)

English - 28 -

Remote control - does not operate

• The batteries may be exhausted. Replace the

bateries.

Input sources - can not be selected

• If you cannot select an input source, it is possible

that no device is connected. if not

• Check the AV cables and connections if you have

tried to connect a device.

Recording unavailable

To record a programme, you should rst connect a

USB disk to your TV while the TV is switched off. You

should then switch on the TV to enable recording

feature. If you cannot record, try switching off the

TV and then re-inserting the USB device.

USB is too slow

If a “USB is too slow” message is displayed on the

screen while starting a recording, try restarting

the recording. If you still get the same error, it

is possible that your USB disk does not meet

the speed requirements. Try connecting another

USB disk.

Appendix A: Nero MediaHome Installation

To install Nero MediaHome, please proceed as

follows:

Note: To use DLNA function, this software should be

installed to your PC.

1. Insert the Nero Media Home installation disc

in your optical disc drive.

• The Nero Multi Installer screen with a button to start

the installation process will open automatically.

• If below window is not displayed automatically,

double-click on the le SetupX located on the Nero

MediaHome installation disc.

2. Click on the button labeled Nero MediaHome

Essentials to start the installation process.

• The Nero MediaHome installation wizard is

displayed.

• If necessary change installation language from

the language selection menu before continuing.

3. Click the Next button.

• The integrated serial is displayed.

• Please do not change displayed serial.

4. Click the Next button.

• The License Conditions (EULA) screen is

displayed.

5. Please read the license agreement carefully

and select the appropriate check box if you

agree to the terms of the agreement. Installation

is not possible without this agreement.

6. Click the Next button.

Software Upgrade

Your TV is capable of nding and updating automatically

via the Aerial/Cable signal or over the Internet.

Software upgrade search via user interface

Simply navigate on your main menu. Choose Settings

and select Other Settings menu. In Other Settings

menu navigate on to the Software for Upgrade item and

press OK button to check for a new software upgrade.

Note : Internet connection is needed. If an internet

connection is not available, try to upgrade via

broadcast. If a new upgrade is found, it starts to

download the upgrade. Press OK to continue with

the reboot operation.

3 AM search and upgrade mode

While the TV is connected to an aerial signal. If

Automatic scanning in the Upgrade Options menu

is enabled, the TV wakes up at 03:00 and searches

broadcast channels for new software upgrades. If

new software is found and downloaded successfully,

the next time the TV powers up , it will have the new

software version.

Note: If the TV fails to come on after the upgrade unplug the

TV for 2 minutes and plug in again.

Troubleshooting & Tips

TV will not turn on

Make sure the power cord is plugged in securely to

wall outlet. The batteries in the remote control may

be exhausted. Press the Power button on the TV.

Poor picture

• Have you selected the correct TV system?

• Low signal level can cause picture distortion.

Please check antenna access.

• Check if you have entered the correct channel

frequency if you have done manual tuning.

• The picture quality may degrade when two

devices are connected to the TV at the same time.

In such a case, disconnect one of the devices.

No picture

• No Picture means that your TV is not receiving a

transmission. Have you selected the correct button

on the remote control? Try once more. Also make

sure the correct input source has been selected.

• Is the antenna connected properly?

• Is the antenna cable damaged?

• Are suitable plugs used to connect the antenna?

• If you are in doubt, consult your dealer.

No sound

• Has the TV been set to mute? To cancel mute, press

the “ ” button, or increase the volume level.

• Sound is coming from only one speaker. Is the balance

set to one extreme? See Sound Menu section.

1 2 ... 24 25 26 27 28 29 30 31 32 33 34 35

Comentários a estes Manuais

Sem comentários

Finlux 47F9076-T Manual do Utilizador Página 29

Comentários a estes Manuais

Manuais e produtos relacionados com TVs LCD Finlux 47F9076-T